Nokia 1280 Restart DONE by Cyclone Box....

Hi ...........Wanna Share This Also Nokia 1280 Restart Problem DONE by Cyclone Box..

Procedure:
1.Open Cyclone Soft.
2.Click DCT4\WD2 Platform.
3.Load Full Flashfile .
4.Click Flash Tab. And Wait Until DONE!!!

Here's The Pic's.....

PHP Code:

Establishing Connection with Box in Main Mode... Handling device: [Cyclone Team], [Cyclone Bootloader], [Platform: Classic] Handling device: [Cyclone Team], [Cyclone Box], [Platform: Classic] Initializing box... Box Firmware: Cyclone Main Application v02.05, (Aug 22 2012 23:26:51, gcc v4.3.3, RTOS V6.0.1), Type: Signed Production Application, (C) KarwosSoft 2012
Hardware Platform: Cyclone Classic Flasher Interface (c) 2008,2009 KarwosLabs
Box Serial Number: C0008558
HW Revision: C, Suitable for: Production, Case: 2011 - New Casing, MCU Manufacture Time: 2011, wk09
Initializing security card... Card Serial Number: D00E0102
Card Firmware Revision: 010A
Card is activated
Box is activated
Started box selftests procedure
USB Voltage    4.81v    PASSED
MCU Voltage    3.29v    PASSED
Core Voltage    1.81v    PASSED
VBAT Voltage    1.37v    PASSED
VBAT Voltage    4.79v    PASSED
Box VPP disabled
VPP Voltage    0.04v    PASSED
Internal Box VPP Enabled
VPP Voltage    4.83v    PASSED
Box VPP disabled
VPP Voltage    0.04v    PASSED
External Box VPP Enabled
VPP Voltage    0.02v    FAILED - IGNORED - Probably power supply is not connected
Box VPP disabled
All box selftests passed! Super DCT4 Activation: TRUE
XGold/Blackberry Service Running, Counter: 100
Avaiable Physical Memory: 1.645GB
Avaiable Virtual Memory: 1.824GB
Avaiable Pagefile: 3.1023GB
Initializing FBUS... All initialized - Ready to work
Booting UPP... Sending User Abort Signal... CBUS Request Error -> User abort
Failed to Check DCT4 Flashing Bus -> UPP Not Responding
Sending User Abort Signal... Booting UPP... Failed to Check DCT4 Flashing Bus -> UPP Not Responding
Processing pre-flash tasks... Pre-flash tasks finished
Checking rm647_005.800... Flash file sorted Okay. 1 file(s) embedded into image. Booting X-Gold via ASC (press power-on if used non-battery cable)... X-Gold: Ready, MCU ID: 0x3400 [PBL] : Ready [EBL] : Mode CC [EBL] : Default_RAM_Bootloader [EBL] : Ready
Setting Baudrate to 921600bps... Baudrate Accepted (921600bps) Flash Chip 0x002088C0, ST, Size: 8MBytes
Processing "hw_b2_rm647_r05.800.fls"... Sending Certificate... Certificate Accepted
Erasing 0x00800000-0x00A0FFFF... Flashing at 0x00800000... Flashed 2162688 bytes OK
Erasing 0x00C60000-0x00EAFFFF... Flashing at 0x00C60000... Flashed 2015936 bytes OK
Erasing 0x00FFC000-0x00FFFFFF... Flashing at 0x00FFC000... Flashed 64 bytes OK
Box VPP disabled
Checking rm6470_nai05.80mr... Flash file sorted Okay. 1 file(s) embedded into image. Booting X-Gold via ASC (press power-on if used non-battery cable)... X-Gold: Ready, MCU ID: 0x3400 [PBL] : Ready [EBL] : Mode CC [EBL] : Default_RAM_Bootloader [EBL] : Ready
Setting Baudrate to 921600bps... Baudrate Accepted (921600bps) Flash Chip 0x002088C0, ST, Size: 8MBytes
Processing "hw_b2_rm6470_nai05.80mr.fls"... Sending Certificate... Certificate Accepted
Erasing 0x00EB0000-0x00F7FFFF... Flashing at 0x00EB0000... Flashed 312768 bytes OK
Box VPP disabled
Checking rm647_005.80mr... Flash file sorted Okay. 1 file(s) embedded into image. Booting X-Gold via ASC (press power-on if used non-battery cable)... X-Gold: Ready, MCU ID: 0x3400 [PBL] : Ready [EBL] : Mode CC [EBL] : Default_RAM_Bootloader [EBL] : Ready
Setting Baudrate to 921600bps... Baudrate Accepted (921600bps) Flash Chip 0x002088C0, ST, Size: 8MBytes
Processing "hw_b2_rm647_005.80mr.fls"... Sending Certificate... Certificate Accepted
Erasing 0x00210000-0x0045FFFF... Flashing at 0x00210000... Flashed 1149056 bytes OK
Box VPP disabled
Processing post-flash tasks... Setting Factory Defaults... Factory defaults OK
Post-flash tasks finished... Flash successfully finished!